Fake Delay

Thanks to Dan Stesco www.danstesco.ro for providing us with this trick.

This doesn’t apply to the microSTATION only, but since the effects processor of that little board is limited, and not as flexible like his older brothers, we need to look for options to combine different effects. So, lets get to it:

The thing is, I’m rebooting my Genesis cover band with a few friends, and my son as the drummer. So, I got a microSTATION, expecting to recreate all the sounds I used to have on my M50, but to my horror, I can’t assign effects freely as I could with the M50. There are so many effects available depending on the slots, if they are IFX or MFX or TFX. So, I need to use them wisely.

I was building a combi for Fading Lights, including an arpeggio pattern to mimic the drum machine that Tony Banks used back in 1992. But, the sound have a delay kind of effect. Now, if I put Chorus, which is vital for any Genesis sound, and add some reverb, to give the sound ambience and presence, I can’t use the delay effect anywhere else. And if I use the delay for the drum machine, I can’t use reverb, and the whole sound is bland and flat.

So what can we do?

 

Well, first of all, duplicate the timbre that the arpeggiator is using, in my case Timbre #5 House Kit, to Timbre #6. Copy all the parameters, but reduce the volume to around 40% compared to Timbre #5. That way, the delay, or “Echo” will be fainter than the main sound, which is the idea.

Remember to assign Arpeggiator A on both timbres, since we want it to play on both, only dephased by a bit.

 

Now the trick. Put a delay on Timbre #6 (the fainter one), I used 800ms, but you can adjust it to your taste.

And that’s it. Now you have delay, without using an FX slot. As simple as that.

Again, thanks Dan.

Power Supply Mod – microSTATION edition

Well, some of you might remember the mod I did for my M50, in which I installed the power supply inside the case, and used an old PC power supply jack embedded in the metal back panel. I remember that flimsy power jack was a nightmare. More than once, it sprung out of its jack, and in the middle of a song. Aghhh!!! With this mod, the issue was fixed once and for all.

This mod have the added bonus of not having to think about packing the power supply, or dealing with the thin cable, so I decided to move on and do the same on my microSTATION. As a matter or fact, this is the third mod I do, since I also did it to my old Roland A33 controller, so kind of I know what I’m doing 😉

So, lets get to it, and please share it.

First of all, you have to cut open a hole on the back panel to fit the power jack. Make it fit snugly, to minimize movement. There are some jacks that have ears for screws, but I’m using one with retaining pressure fins, which I believe look cleaner. Although, if it were a metal panel, I would have gone with the screws version.

Next, dismount the little board that have the power jack, unplug the switch and remove a couple screws on the outside, and one on the board itself. turn it over, and you’ll see where the jack is soldered to the board. These are the soldering spots you will be testing for continuity. For this, you’ll have to cut the adapter cable (yeah, ouch!) but is worth it. Now, connect the stripped wire to the tester, put the plug in the jack, and check the solder points. The one that makes contact is the positive. Do the same to the other wire.

The next step is to solder the adapter prongs to the connectors on the rear side of the power jack. I used some copper wire around the connectors and the prongs, since both have a hole in the middle, so is easier to wrap the wire around. No need to be too much. I only did one turn. I just wanted to have something to make the solder adhere to.

 

Adapter in place. Poured some hot glue around the prongs, just to cover and avoid any possible short, and also below the adapter itself, to make it adhere to the plastic case. it won’t move too much, being soldered to the jack, but I just wanted extra safety. I don’t want the adapter banging around inside the case.

 

Next, soldering. If you are not comfortable using a soldering iron, look for someone who is. Is not a highly miniaturized device, that requires special soldering abilities. Is just simply heating up the points already on the board, enough to melt the solder a bit to make the cable stick, and put a bit more solder around them. That is all in reality. No rocket science.

I also made a small loop on the cable, and secured it against one of the board corner holes with a small zip tie, just to avoid any tension.

 

Board back in place, and as you can see, is hardly noticeable that something is attached to the back of the board. A very clean job.

 

 

 

 

Mission accomplished. And ready to close the case.

 

 

 

 

Its Alive!!!

 

 

Enjoy

Genesis Sounds

Genesis Tony Banks Sounds

An insight on the sounds of many popular Genesis songs

By: Santi Jansen (www.wecantdance.nl)

Compiled by: Martin Ocando

Introduction

Genesis Tony Banks sounds is a compilation of several posts in korgforums.com trying to emulate the synthesizer sounds we learned to love in every Genesis live performance. Is obvious that trying to get the exact same sound will require a duplicate of all gear used by Tony, but only Tony or Genesis can afford such a gigantic collection of hardware. We are simply trying to dissect every single sound down to the wave element and apply filters, lfo’s, envelopes and effects to get as close as possible.

These recommendations don’t have a specific synthesizer model or make, although Santi does mention them for reference, but if followed by the letter it can be applied to many models.

I feel the need to express my most sincere thanks to Santi for sharing his knowledge and experience. His words will provide all Genesis lovers and keyboardists, either pro or amateur, with lots of satisfaction and emotion, since the feeling of playing what we have loved to hear for generations is incommensurable.